rockford amplifiers

I sold my last system(a 600 watt power acoustik amp and 2 mtx 10's) and now I have an 800 wattx2 Rockford Fosgate Punch amplifier. I have a non ported box that holds 2 twelve inch subwoofers, I have 4 6x9 door speakers and a pioneer stereo. What two subs would hit best with my amplifier?

I agree with the last poster on alot of stuff. One good sub is much better than two cheap subs. The quality is much better and the output usually is at least on par.

I try to stick with the same brand when I can, so if you have a RF amp see what RF powers for subs with it. That should give you an idea of what the amp was designed to do.

I've also had good luck with JL speakers, especially the W6v2's, the Alpine Type R's, and lots of other good name brand subs.

2008-03-30 18:13:09 by Big Daddy

I have a rockford fosgate amplifier its the t2500 1bd im hooking it up to two t2 12s rockford fogate also just wondering if anyone has any idea if its going to sound good.

U never go wrong with Fosgate bro

2009-03-29 20:30:59 by amanda b

HPP plating for superior corrosion resistance
Accepts 1/0 AWG or 4 AWG wire.
Custom tooled solid brass

i have rockford rosquate amplifier 4600x series and jl audio subs i have no idea how much they are worth i am trying to sell them anyone have an estimate?

THE BEST THING TO DO IS SEARCH EBAY AND CRAIGSLIST TO SEE THE GOING PRICE IT REALLY DEPENDS ON THE DEMAND FOR EACH UNIT

2007-11-02 12:18:22 by bs99dan

Price: $94.99

Stamp Cast Frame Structure
Linear spider with embedded 16 AWG tinsel leads
Kevlar Fiber Reinforced Paper Cone
Integrated PVC Trim Ring
Mica injected polypropylene cone with poly-foam surround

I finally got my ride almost where I want to be! However I think I might be having buyers remorse, but i haven't installed my amps yet! I was wanting to know since I am doing a 2 amp configuration! I have currenty in the box the Rockford Fosgate t400-4 which is for my front components and rears, and T1500 for my 2 /12" Rockford subwoofers! Keep in mind I haven't put this in yet! However this Alpine series the PDX has got me really intrigued the 4.150 which is 100 watts continuous power at 4 or 2ohm, where as my Rockford Fosgate is only 60 at 4 ohm! Then they have the Alpine PDX1.1000 for the mono which is 1000 continuous watts! I think my Rockford Fosgate breaks down like this T1500continuous power:
500W x 1 @ 4-Ohms RMS
1000W x 1 @ 2-Ohms RMS
1500W x 1 @ 1-Ohm RMS
So did I make a bad or good decsion by listening to the car audio people! I hear the PDX amplifiers get hot, but they put out so much power it seems for soemthing so small! Or am I simply underestimating Rockford?
Thanks for the quick reply, here's the answer to your question my 2 subs are the Rockford P3D412 dual 4 ohms, RMS/ Peak: 500 Watt /1000 watts! I got a set of MB quart signature component speakers in the front and the DTF-169 in the rear!

whats the rms and the ohms on your subs???? if i knew that it would be easier to answer

edit: as far as the amps go if your speakers can handle 100rms i would go with an amp that 100rms, but i wouldnt go with the rockford or alpine. i have nothing against rockford, but they are overpriced. and i dont like alpine. go for mtx. they are great amps and the new models even have an led setup built in that u can set to different colors to match whatever you want and gives you a lighted look without having to add neons. for the speakers id go with this http://www.onlinecarstereo.com/CarAudio/ ProductDetail.aspx?ProductID=15179
as for subs im not sure yet till you give the rms and ohms of the subs

edit: you can wire each sub to 2ohm or you can wire them 2gether down to 1ohm. for amp id go with this
http://www.sonicelectronix.com/item_5647 _MTX+Audio+TA81001+Thunder+81001.html# wire the subs to 2ohm and the sub has 2 inputs so u can connect each to the amp instead of going to a 1ohm load and u push the full 1000rms