Standing Stereo Speakers

I have a very old Panasonic home stereo system and some huge floor- standing speakers. I would like to replace the floor-standing speakers with some shelf speakers. What specifications should I look for to ensure that I don't destroy my system?

Thanks!

i would check the impedance for the speakers, it should be on the back where you hook them up, it should be measured in ohms and the symbol should look like a horse shoe.

2009-05-09 19:51:55 by purplehaze

SONY FLOOR STANDING SPEAKERS 2X200WATTS

I don't know, but you could try asking at this yahoo group:

http://tech.groups.yahoo.com/group/IMF-e lectronics/

And here's a couple of other sites you might find interesting!

http://www.t-linespeakers.org/

http://imf-electronics.com/

Good luck!

Gx

2008-04-17 02:36:54 by ROBERT B

Price: $499.00 $499.00

Exclusive Convergent source Module features woofer and tweeter uniquely integrated for accurate sound and expansive soundstage.
Rigid, low-distortion cross-braced MDF enclosure with attractive Black Ash Finish and Black High Gloss trim.
Port plug carpet spikes included.
Dual 6.5-Inch Woofers and 5.5-Inch midrange feature patented Ribbed Elliptical Surround suspension for greater dynamics
Exclusive 1-Inch Hyperbolic Aluminum tweeter provides high frequency accuracy, high power-handling and wide dispersion

any ideas what brands will be good to look into? I've been looking at Klipsch, Polk, Pure Acoustics and Infinity and what not and really, i haven't heard many of them to get an idea of the general sound of each brand. I dont really know where to go to test any of these out either. So i guess this question is just about other brands to consider that aren't thousands and thousands of dollars

The brands you mentioned are good brands, and have speakers in a wide range of prices. There are also many other (Bose, Jamo, AR, etc.) However, if you care about sound quality, you should audition the speakers. Even high-quality speakers sound different, and often it is only a matter of taste as to which you would prefer. If you are going to spend significant money on a good system, it is worth it to spend the time to listen to as many as you can. You might also listen to some very high-end units (you wouldn't buy) just to set a reference as to what the best sound like.

2009-02-27 19:17:57 by twinreverb73

Price: $999.00 $999.00

Frequency Range: 30-24,000Hz
A single top of the line stereo and surround speaker
All front speakers in the C 80 series feature bi-wiring
Equipped with two 7" woofers, one 7" midrange and one 1" DTT (Decoupled Tweeter Technology) tweeter
Uses Hard Conical Cone and Centre-Plug technology

http://www.oaktreeent.com/web_photos/Ste reo_Speakers/Yamaha_NS-A3500A_Stereo_Spe akers_collage.jpg

thats what it looks like. all it has on the back is the red and black thing shown in the pic. It does not look like a port to me, and i dont know how to use it.
the red and black thing is not like a regular port. it does not fit in flushly at all.

The red and black connections are for speaker wire, and there will be corresponding red and black connectors on the back of the amplifier/receiver. Speaker wire, whatever the colour, has one plain coloured wire and one with a black stripe. This is how you use the connectors.

Bare the ends of both wires, take off about 8-10mm of the plastic cover and twist the bare end of each wire so you don't get any strands of wire sticking out. Take the plain coloured wire and hold down the little red tab on the back of the speaker. Push the bare end of the plain coloured wire into the little hole just above the tab. Let go of the tab. It will spring back up and hold the bare part of the wire tightly. Make sure that there are no strands of bare wire hanging out. Now do the same with the wire which has the black stripe. Put that into the black connector on the speaker.

Now connect the other ends of the wires to the amplifier in exactly the same way - plain colour to red, striped wire to black.

By the way, that's a very fine pair of speakers you have there, even by today's standards.

2009-03-29 16:05:20 by law

When looking at stereo speaker equipment, there are 'watt' ratings [eg: 50watts] and 'RMS' ratings [eg: 50watts rms] .... I'd like to know what 'RMS' is and the difference between rms and watts.

RMS is the watts rating that your speakers will output on a continuous basis.....so if your speakers are 50 watts RMS and it says that the peak power output is 75 watts it means that no matter what you are getting at least 50 but in some conditions/volume levels it can go up to 75 watts.

2007-09-15 19:08:41 by Hermione